Wednesday, July 25, 2012
Specialist in Environmental Policy
Hydraulic fracturing is a technique developed initially to stimulate oil production from wells in declining oil reservoirs. With technological advances, hydraulic fracturing is now widely used to initiate oil and gas production in unconventional (low-permeability) oil and gas formations that were previously inaccessible. This process now is used in more than 90% of new oil and gas wells. Hydraulic fracturing is done after a well is drilled and involves injecting large volumes of water, sand (or other propping agent), and specialized chemicals under enough pressure to fracture the formations holding the oil or gas. The sand or other proppant holds the fractures open to allow the oil or gas to flow freely out of the formation and into a production well.
Its application, along with horizontal drilling, for production of natural gas (methane) from tight gas sands, unconventional shale formations, and coal beds, has resulted in the marked expansion of estimated U.S. natural gas reserves in recent years. Similarly, hydraulic fracturing is enabling the development of tight oil resources, such as the Bakken and Eagle Ford formations. However, the rapidly increasing and geographically expanding use of fracturing, has raised concerns over its potential impacts on groundwater and drinking water supplies, and has led to calls for greater state and/or federal oversight of this activity.
Historically, the Environmental Protection Agency (EPA) had not regulated the underground injection of fluids for hydraulic fracturing of oil or gas production wells. In 1997, the U.S. Court of Appeals for the 11th Circuit ruled that fracturing for coalbed methane (CBM) production in Alabama constituted underground injection and must be regulated under the Safe Drinking Water Act (SDWA). This ruling led EPA to study the risk that hydraulic fracturing for CBM production might pose to drinking water sources. In 2004, EPA reported that the risk was small, except where diesel was used, and that national regulation was not needed. However, to address regulatory uncertainty the ruling created, the Energy Policy Act of 2005 (EPAct 2005) revised the SDWA term “underground injection” to explicitly exclude the injection of fluids and propping agents (except diesel fuel) used for hydraulic fracturing purposes. Consequently, EPA currently lacks authority under the SDWA to regulate hydraulic fracturing, except where diesel fuel is used. (In May, EPA issued draft permitting guidance for use of diesel during fracturing.) As the use of this process has grown, some in Congress would like to revisit this statutory exclusion.
Several relevant bills are pending. H.R. 1084 and S. 587 would repeal the exemption for hydraulic fracturing operations established in EPAct 2005, and amend the term “underground injection” to include explicitly the injection of fluids used in hydraulic fracturing operations, thus authorizing EPA to regulate this process under the SDWA. The bills also would require disclosure of the chemicals used in the fracturing process. S. 2248 and H.R. 4322 would specify that a state has sole authority to regulate hydraulic fracturing on federal lands within state boundaries. EPA’s FY2010 appropriations act urged the agency to study the relationship between hydraulic fracturing and drinking water quality. Interim and final reports are expected in 2012 and 2014, respectively. Meanwhile, numerous states are reviewing or have revised their oil and gas rules to address the increased use of high-volume hydraulic fracturing.
This report reviews past and proposed treatment of hydraulic fracturing under the SDWA, the principal federal statute for regulating the underground injection of fluids to protect groundwater sources of drinking water. It reviews current SDWA provisions for regulating underground injection activities, and discusses some possible implications of, and issues associated with, enactment of legislation authorizing EPA to regulate hydraulic fracturing under this statute.
Date of Report: July 12, 2012
Number of Pages: 42
Order Number: R41760
Document available via e-mail as a pdf file or in paper form.
R41760.pdf to use the SECURE SHOPPING CART
For email and phone orders, provide a Visa, MasterCard, American Express, or Discover card number, expiration date, and name on the card. Indicate whether you want e-mail or postal delivery. Phone orders are preferred and receive priority processing.
Follow us on TWITTER at http://www.twitter.com/alertsPHP or #CRSreports
Posted by Penny Hill Press, Inc. at Wednesday, July 25, 2012